miniZ v1.8z2 is out!

Hi everyone,

A new miniZ version v1.8z2 is out with improved and increased support for AMD mining –  125,4; 144,5; and ethash/etchash!

For detailed changelog, read below.

Please find miniZ version v1.8z2 Download page.

miniZ v1.8z2 is out!


  • Added AMD support for ETH, for Ellesmere GPUs and gfx1031 (RX 6700 XT) GPUs.
  • Added AMD support for 144,5, for Ellesmere GPUs and gfx1031 (RX 6700 XT) GPUs.
  • Fixed support for AMD GPUs, on Windows.
  • Fixed issues with AMD support for 125,4 (Flux), for Ellesmere GPUs and gfx1031 (RX 6700 XT) GPUs.

OCs for LHR GPUs mining ETH  (sudo recommended, in Linux)
We also leave here information regarding the OCs we used for testing (driver 510.54). Note that you may need to adjust a bit for your system. We recommend using sudo in Linux when mining ETH with LHR GPUs.

  • 3060: core: -100, mem:+2990 (Linux)*, PL=115 W; ~39 MH/s
  • 3070 Ti: core: -200, mem: +4500 (Linux)*, PL=215 W; ~65 MH/s
  • 3080 Ti: core: +0, mem: +2600 (Linux)*, PL=266 W. ~79 MH/s (~84 MH/s with proper cooling)

* On Windows, memory clock with MSI Afterburner should be half of the indicated value. For example, for the 3080 Ti you need to set +1300 for memory clock in MSI Afterburner. Note that you may need to adjust a bit for your system.

*** Thank you all for the feedback! ***

Remember to try --oc1/--oc2/--ocX options for optimum performance.

For additional information check our Usage or FAQ pages.

*** Download miniZ version v1.8z2 here. ***

Engage, feedback and support

Because your feedback is very important, miniZ kindly encourages you to use the comment box below for general questions and feedback.

Certainly we will strive to help you with any doubt and provide a solution to any problem you may encounter. In case you need to reach us, please check the Support page.

Follow us
On Twitter
Our thread on

We wish you a fast and friendly mining experience!



  1. Baba says:

    Hi, I was happy with AMD but it still doesn’t support 6600XT at algo 125.4.This version does not change much, but there are no problems Nvidia with 512.12 drivers:CC +250 MC 0power 70w3060ti – 50 Sol/s /flux/3070ti – 70 Sol/s /flux/I hope to add other AMDsoon,Thanks

  2. ZeroII says:

    How can i fix this?************ miniZ v1.8z ************Number of miniZ CUDA>=[8.0] using driver CUDA[0.00] devices found: 1miniZ<144,5>[00:0:00.0:1598]: Selecting GPU#0[0] NVIDIA GeForce MX450[FATAL ] GPU[00] has invalid mode 0.[INFO ] Disconnecting from

    • miniZ says:

      Hi ZeroII,
      Your gpu is turing… miniZ doesn’t have a kernel for 2GB GPUs with that architecture.

  3. Bob says:

    Are overclock profiles, memclock, cclock, power limit settings, etc able to be set in a config file for windows?

    • miniZ says:

      Hi Bob,
      Not at the moment.
      Also, it will not be implemented in the next release.
      But we’ll work on it for other future release.
      Thanks for the suggestion.

    Leave a Reply

    Your email address will not be published.

    I accept the Privacy Policy